Hardware Specification
| Technical item | Details |
| PON Interface | 1 GPON BOB (Bosa on Board) |
| Receiving sensitivity: ≤-27dBm | |
| Transmitting optical power: 0~+5dBm | |
| Transmission distance: 20KM | |
| Wavelength | TX: 1310nm, RX: 1490nm |
| Optical Interface | SC/APC Connector |
| Chip Spec | RTL9602C,DDR2 64MB |
| Flash | SPI Nor Flash 16MB |
| LAN Interface | 1 x 10/100/1000Mbps(GE) and 1 x 10/100Mbps(FE) auto adaptive Ethernet interfaces. Full/Half, RJ45 connector |
| Wireless
|
Compliant with IEEE802.11b/g/n, |
| Operating frequency: 2.400-2.4835GHz | |
| support MIMO, rate up to 300Mbps, | |
| 2T2R,2 external antenna 5dBi, | |
| Support: Multiple SSID | |
| Channel: Auto | |
| Modulation type: DSSS, CCK and OFDM | |
| Encoding scheme: BPSK, QPSK, 16QAM and 64QAM | |
| CATV Interface
|
RF, WDM, optical power : +2~-15dBm |
| Optical reflection loss: ≥45dB | |
| Optical receiving wavelength: 1550±10nm | |
| RF frequency range: 47~1000MHz, RF output impedance: 75Ω | |
| RF output level: 78dBuV | |
| AGC range: -13~+1dBm | |
| MER: ≥32dB@-15dBm | |
| LED | 9 LED, For Status of WIFI、WPS、PWR 、LOS 、PON 、LAN1~LAN2、 Worn、 Normal(CATV) |
| Push-Button | 3,For Function of Factory Reset, WLAN, WPS |
| Operating Condition | Temperature: 0C~+50C |
| Humidity: 10%~90% (non-condensing) | |
| Storing Condition | Temperature: -30C~+60C |
| Humidity: 10%~90% (non-condensing) | |
| Power Supply | DC 12V/1A |
| Power Consumption | ≤6W |
| Dimension | 180mm×107mm×28mm (L×W×H) |
| Net Weight | 0.2Kg |
Panel lights Introduction
| Pilot Lamp | Status | Description |
| WIFI | On | The WIFI interface is up. |
| Blink | The WIFI interface is sending or/and receiving data (ACT). | |
| Off | The WIFI interface is down. | |
| WPS | Blink | The WIFI interface is securely establishing a connection. |
| Off | The WIFI interface does not establish a secure connection. | |
| PWR | On | The device is powered up. |
| Off | The device is powered down. | |
| LOS | Blink | The device doses not receive optical signals or with low signals. |
| Off | The device has received optical signal. | |
| PON | On | The device has registered to the PON system. |
| Blink | The device is registering the PON system. | |
| Off | The device registration is incorrect. | |
| LAN1~LAN2 | On | Port (LANx) is connected properly (LINK). |
| Blink | Port (LANx) is sending or/and receiving data (ACT). | |
| Off | Port (LANx) connection exception or not connected. | |
| Worn (CATV) | On | Input optical power is higher than 3dbm or lower than -15dbm |
| Off | Input optical power is between -15dbm and 3dbm | |
| Normal(CATV) | On | Input optical power is between -15dbm and 3dbm |
| Off | Input optical power is higher than 3dbm or lower than -15dbm |
Functional Feature
◼ Support EPON/GPON mode and switch mode automatically
◼ Support Route mode for PPPoE/IPoE/Static IP and Bridge mode
◼ Support IPv4 and IPv6 Dual mode
◼ Support 2.4G WIFI 802.11 b/g/n and 2*2 MIMO
◼ Support CATV interface for Video Service and remote control by Major OLT
◼ Support LAN IP and DHCP Server configuration
◼ Support Port Mapping and Loop-Detect
◼ Support Firewall function and ACL function
◼ Support IGMP Snooping/Proxy multicast feature
◼ Support TR069 remote configuration and maintenance
◼ Specialized design for system breakdown prevention to maintain stable system
Appearance
Application
◼ Typical Solution：FTTH(Fiber To The Home)
◼ Typical Business：INTERNET 、 IPTV 、WIFI 、CATV etc
Figure: HUR2102XR Application Diagram
Products categories
Write your message here and send it to us